Nokia Compatible 3HE10550AA-20-FL Quick Spec:

Nokia 3HE10550AA-20-FL Datasheet (100GBase, LR4, QSFP+, SMF, 20km, Dual-LC, COM, EXT, IND) Fiber Optic Transceiver

Part Number: 3HE10550AA-20-FL 3HE10550AA-20-EXT-FL

3HE10550AA-20-IND-FL


Form Factor: QSFP28

TX Wavelength: 1295/1300/1304/1309nm

Reach: 20km

Cable Type: SMF

Rate Category: 100GBase

Interface Type: LR4

DDM: Yes

Connector Type: Dual-LC


Nokia Compatible 3HE10550AA-20-FL Features


Nokia Compatible 3HE10550AA-20-FL General Description

The FluxLight 3HE10550AA-20 is a 100Gb/s transceiver module designed for optical communication applications compliant to 100GBASE-LR4 of the IEEE 802.3ba standard. The module converts 4 input channels of 25Gb/s electrical data to 4 channels of LAN WDM optical signals and then multiplexes them into a single channel for 100Gb/s optical

transmission. Reversely on the receiver side, the module de-multiplexes a 100Gb/s optical input into 4 channels of LAN WDM optical signals and then converts them to 4 output channels of electrical data.


The central wavelengths of the 4 LAN WDM channels are 1295.56, 1300.05, 1304.58 and 1309.14 nm as members of the LAN WDM wavelength grid defined in IEEE 802.3ba. The high-performance cooled LAN WDM DFB transmitters and high sensitivity PIN receivers provide superior performance for 100Gigabit Ethernet applications up to 20km links and compliant to optical interface with 100GBASE-LR4 requirements specified in IEEE 802.3ba Clause 88.


Absolute Maximum Rating

The operation in excess of any absolute maximum ratings might cause permanent damage to this module.

Parameter

Symbol

Min

Max

Unit

Notes

Storage Temperature

TS

-40

+85

degC


Operating Case Temperature

TOP

0

70

degC


Power Supply Voltage

VCC

-0.5

3.6

V


Relative Humidity

RH

0

85

%

non- condensation

Damage Threshold, each Lane

THd

5.5


dBm



Recommended Operating Conditions

Parameter

Symbol

Min

Typical

Max

Unit

Notes

Operating Case Temperature

TC

0


+70

degC


Data Rate Accuracy


-100


+100

ppm


Control Input Voltage High



2

Vcc

V


Control Input Voltage Low


0.8



V


Link Distance with G.652




20

km



Electrical Characteristics

The following electrical characteristics are defined over the Recommended Operating Environment unless otherwise specified

Parameter

Symbol

Min

Typical

Max

Unit

Notes

Supply Voltage

Vcc

3.135


3.465

V


Supply Current

Icc



1.15

A


Module total power

P



4

W



Optical Characteristics

Parameter

Symbol

Min

Typical

Max

Unit

Notes


Wavelength Assignment

L0

1294.53

1295.56

1296.59

nm


L1

1299.02

1300.05

1301.09

nm


L2

1303.54

1304.58

1305.63

nm


L3

1308.09

1309.14

1310.19

nm


Transmitter

Side Mode Suppression Ratio

SMSR

30



dB

1

Total Average Launch Power

PT



10.5

dBm


Average Launch Power, each Lane

PAVG

-4.3


4.5

dBm


Extinction Ratio

ER

4



dB



Average Launch Power OFF Transmitter, each Lane

Poff



-30

dBm


Receiver

Damage Threshold, each Lane

THd

5.5



dBm


Average Receive Power, each Lane


-10.6


4.5

dBm


Receiver Sensitivity, each Lane(OMA)

SEN

-8.6


4.5

dBm


Receiver Reflectance

RR



-26

dB


LOS Assert

LOSA

-24



dBm


LOS Deassert

LOSD



-11.6

dBm


LOS Hysteresis

LOSH

0.5



dB



Recommended Power Supply Filter


1521701475(1)


Digital Diagnostic Functions

The following digital diagnostic characteristics are defined over the normal operating conditions unless otherwise specified.

Parameter

Symbol

Min

Max

Unit

Notes

Temperature monitor absolute error

DMI_Temp

-5

5


Supply voltage monitor absolute error

DMI_VCC

-0.1

0.1

V


Channel RX power monitor absolute error

DMI_RX_Ch

-3

3

dB


Channel Bias current monitor

DMI_Ibias_Ch

-10%

10%

mA


Channel TX power monitor absolut error

DMI_TX_Ch

-3

3

dB



Mechanical Dimensions

Units: mm

image


Pin Assignment and Description


image


Pin Assignment


报纸上的文字

描述已自动生成


image


image

RoHS Compliance

FluxLight is fully committed to environment protection and sustainable development and has set in place a comprehensive program for removing polluting and hazardous substances from all of its products. The relevant evidence of RoHS compliance is held as part of our controlled documentation for each of our compliant products. RoHS compliance parts are available to order, please refer to the ordering information section for further details.


ESD

This transceiver is specified as ESD threshold 1kV for SFI pins and 2kV for all other electrical input pins, tested per MIL- STD-883, Method 3015.4 /JESD22-A114-A (HBM). However, normal ESD precautions are still required during the handling of this module. This transceiver is shipped in ESD protective packaging. It should be removed from the packaging and handled only in an ESD protected environment.


Laser Safety

This is a Class 1 Laser Product according to EN 60825-1:2014. This product complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50, dated (June 24, 2007).

Caution: Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.


Licensing

The following U.S. patents are licensed by Nokia to FluxLight, Inc.:

U.S. Patent Nos: 7,184,668, 7,079,775, 6,957,021, 7,058,310, 6,952,531, 7,162,160, 7,050,720



image